Clutch Disc Plate XCMG XKT136-manufacture,factory,supplier from China

Product descriptionThe clutch plate is an important part of the clutch. It is a round steel plate. These are usually made of friction material that is attached to the engine's crankshaft. The purpose of the mounting plate is to transfer engine power to the gearbox. When releasing the clamp, the mounting plates stick together due to friction and rotate together. In this way, the power from the engine is transferred through the pressure plate to the transmission, propelling the vehicle forward.

Product description Withstand Pressure: The clutch pressure plate takes the strain from the seize strain plate spring and transmits it between the grab disc and flywheel to make sure the applicable operation of the clutch.Metal Material: Clutch stress plate is normally made of excessive electricity steel material, such as metal or aluminum alloy, to make sure adequate energy and durability.Friction surface: The grasp stress plate commonly has a friction floor that serves to make contact with the grasp disc to furnish friction so that the snatch disc can desirable contact and disengage from the

Product descriptionA clutch is similar to a switch, engaging or disengaging power transmission. The active part and the driven part of the clutch mechanism can be temporarily separated, and can be gradually connected, and may also rotate relative to each other during the transmission process. There cannot be a rigid connection between the driving part and the driven part of the clutch.

Product detailsThe clutch is an important component required in the vehicle transmission system, and the automobile clutch driven plate is an important wear component of manual transmission cars.

Product descriptionCeramic brake pads use high-tech materials such as large-grain graphite/brass/high-grade ceramics (non-asbestos) and semi-metals, which have the advantages of high temperature resistance, wear resistance, stable braking, repair of brake discs, environmental protection, no noise and long service life. Excellent material properties, overcoming the material and process defects of traditional brake pads, it is the most cutting-edge advanced ceramic brake pad in the world.

Detailed introduction of clutch driven plate:1. Principle: The clutch is located in the flywheel housing between the engine and the gearbox. The clutch assembly is fixed on the rear plane of the flywheel with screws. The output shaft of the clutch is the input shaft of the gearbox. While the car is driving, the driver can depress or release the clutch pedal as needed to temporarily separate and gradually connect the engine and the transmission to cut off or transmit the power input from the engine to the transmission.2.

Product descriptionThe automobile clutch driven plate is an indispensable wearing part for manual transmission cars. It transmits the engine torque to the transmission through friction conversion, reduces the vibration and impact of the transmission system, and completes the "disengagement" and "engagement" tasks. The clutch driven plate is mainly composed of driven plate, driven plate hub, friction plate and other parts. They work together to provide smooth and stable performance and make the clutch work efficiently.1.

The driven plate assembly is mainly composed of friction plate, driven plate, shock absorber and spline hub. The driven plate has a great influence on the working performance of the clutch and should meet the following design requirements:1. The moment of inertia should be as small as possible to reduce the impact between gear teeth when the transmission is shifting.2. It should have axial elasticity to make the clutch engagement smooth and easy to start, and to make the pressure on the friction surface uniform and reduce wear.3.

Features of Clutch Disk For XCMG XKT136There are 6 corrugated spring steel plates around the driven plate steel plate, and 6 window holes are evenly arranged on the corrugated spring steel plate. The driven plate steel plate communicates with the first friction lining and the second friction lining respectively through the window holes.

Products DescriptionSmooth surface without burrs.All over the world.Factory direct sales.Professional after sales.High strength and uniform force SpecificationProduct NameClutch CoverCertificateIATF16949:2016Place of Origin Shandong,ChinaWarranty12 MONTHSLogistics port Shanghai/Ningbo/QingdaoTruck Model XCMG,LCMG,SDLG,SANY,LiuGong,TONLY,CNHTCSupply Ability120000 Sets/MonthClutch Cover SizeStandardQuality100% Professional TestClutch Disc SizeOE StandardBrand NameLHweight30 kgPackageStandrad PackageConditionNewHow to make offer:Provide OE Number, Tech

Product descriptionThe clutch is located in the flywheel housing between the engine and gearbox. The clutch driven plate is mainly composed of a driven plate body, a friction plate and a driven plate hub. Specifically, it can be said that it is composed of four parts: driven steel plate, friction plate, torsion damper, and driven disc hub. Driven steel plate: The driven steel plate is riveted to the torsional shock absorber disc, and the driven disc hub is sandwiched between them. Friction plate: transmits torque.

Product description The seize disc is an necessary section of the clutch. It is a round steel disc, normally made of friction material, installed on the crankshaft of the engine. The function of the seize plate is to transmit engine strength to the transmission.When the grasp pedal is released, the friction between the seize plate and the grab power plate will purpose them to come into shut contact and rotate together.

Product descriptionThe clutch drive plate mainly consists of the drive plate, drive plate hub, friction plate and other parts.1. The material of the driven parts is related related to the structural model used2. Followers without wave spring blades usually It is forged from high carbon steel or spring hardened parts and has been heat treated to provide This meets the hardness requirements.3. When using a wave spring plate, the follower should be made of Low carbon steel and corrugated parts should be made. from spring steel4. Drive disc hubs are generally made of 26-32HRC cast iron.5.

Product description Withstand Pressure: The clutch pressure plate takes the pressure from the clutch pressure plate spring and transmits it between the clutch disc and flywheel to ensure the proper operation of the clutch.Metal Material: Clutch pressure plate is usually made of high strength metal material, such as steel or aluminum alloy, to ensure sufficient strength and durability.Friction surface: The clutch pressure plate usually has a friction surface that serves to make contact with the clutch disc to provide friction so that the clutch disc can properly contact and disengage from

Product DescriptionThe clutch plate requires a certain amount of friction to transmit enough power. At the same time, it is also required to have certain wear resistance and high temperature resistance to ensure long-term reliability.The performance and overall performance of the clutch plate directly affect the operating effect and life of the clutch. Therefore, when using and maintaining the clutch, pay attention to the wear degree and condition of the clutch plate.

Product descriptionThe clutch plate is an important part of the clutch. The clutch plate is a round steel plate. They are usually made of friction material attached to the engine crankshaft. The function of the clutch plate is to transmit the engine's power to the gearbox.1. Clutch structure: The clutch is mainly composed of control part, transmission part, contacts, friction plates and other parts. These work together to enable the clutch to work efficiently.2.

Clutch working principle:The clutch is located in the flywheel housing between the engine and transmission. It consists of friction plates, spring plates, pressure plates, and power output shafts. It is located between the engine and the gearbox. The engine oil is stored in the flywheel of the engine. When the driver depresses the clutch, the clutch will actually loosen. This will temporarily disconnect the engine and transmission. The clutch will actually start to move when the driver releases the clutch pedal. In this way, the engine's power is transferred to the transmission system.

Product descriptionAs a component that transmits power, the clutch has three important functions: "transmitting power", "cutting off power" and "preventing overloading". The driven plate, also called the rear pressure plate, exerts force on the clutch friction plate from the rear, making the friction plate slightly Move forward and compress the driving plate (front pressure plate, flywheel) to transmit power.The driven disc is necessary for thermal pressure equalization of the clutch.

Product description The clutch disc is an important part of the clutch. It is a circular metal disc, usually made of friction material, mounted on the crankshaft of the engine. The role of the clutch plate is to transmit engine power to the transmission.When the clutch pedal is released, the friction between the clutch plate and the clutch drive plate will cause them to come into close contact and rotate together.

Product DetailsThe clutch driven plate is mainly composed of driven plate. Wheel hub, transmission plate, friction plate and other partsAdvantages of disc clutch1. Reduce engine loss: The clutch driven disc reduces engine loss and reduces engine loss when the engine speed changes. This improves the engine's fuel efficiency.2. Energy saving and environmental protection: The clutch driven plate can improve engine fuel efficiency. This reduces the vehicle's fuel consumption and emissions. To achieve the purpose of energy saving and environmental protection.3.

Product descriptionThe structure of the clutch driven disc is usually adapted to the material of the driven disc friction plate used. Clutch Disc Ceramic Disc 24 Teeth is: a cermet automotive clutch driven disc, consisting of cermet friction discs, driven discs, and reducers.

Product descriptionThe driven plate is mainly composed of the driven plate body, friction plate and driven plate hub. Specifically, it can be said that it consists of four parts: driven steel plate, friction plate, torsion damper, and driven disk hub. Driven steel plate: The driven steel plate is riveted to the torsional shock absorber disc, with the driven disc hub sandwiched between the two. Friction plate: transmits torque. Torsional shock absorber: can effectively prevent torsional vibration of the transmission system. Driven hub, etc.: transmit torque.

Introduction to automobile clutchA notable feature of the clutch friction plate lining is the production of rivet holes during the baking stage. In a special mold. The notch on the surface helps to better self-clean the wear product and smooth adhesion of the clutch at the beginning of the movement. Elliptical winding pads increase knot wear and guarantee up to 10 million cycles. Every clutch disc is subjected to mandatory factory balance and routine tests: geometry, torque and hysteresis measurements.

Product description1.Starting control: The clutch driven plate controls the engine starting, converts the engine power into vehicle body movement, and realizes engine starting.2. Gear shift control: The clutch driven plate controls the gear shift of the engine speed. By changing the friction of the friction plate, the engine speed can be changed, thereby changing the engine speed.3. Parking control: The engine parking can be controlled through the clutch driven plate. By reducing the friction of the friction plates, the engine speed can be reduced and the engine stopped.4.